|
Description |
Notes |
Date |
|
Preparation of steel substrates before application of paints and related products - Test methods for non-metallic blast-cleaning abrasives. - Part 6 Determination of foreign matter |
|
|
ISO 1461 |
Galvanising |
- |
|
ISO 2063 |
Metallic and other inorganic coatings - Thermal spraying - Zinc, aluminium and their alloys |
- |
1991 |
ISO 2064 |
Metallic and other inorganic coatings - Definitions and conventions concerning the measurement of thickness |
- |
- |
ISO 2178 |
Metallic and related coatings: meas. of coating on magnetic metals |
Magnetic gauge. Factors affecting accuracy. Calibration and use. |
- |
ISO 2360 |
Metallic and related coatings: meas.of coating on non-mag. metals |
Eddy current gauge. Factors affecting accuracy. Calibration & use. |
1982 |
ISO 2409 |
Paints and varnishes - cross-cut test. |
Tool, 1mm for 0-60 mic on hard sub, 2mm for 0-60 mic on soft or 61-120 mic on both hard and soft substrates; soft brush; lens x2 or x3; adhesive tape 10N/25mm. Use and classification table. |
1992 |
ISO 2746-CD |
Vitreous and porcelain enamels - Enamelled articles for service under highly corrosive conditions - High voltage test |
Discussion document. High voltage test method. |
1994 |
ISO 2808-3 |
Paints and varnishes - determination of film thickness. |
Method 3 - Dial gauge. |
1991 |
ISO 2808-5B |
Paints and varnishes - determination of film thickness. |
Method 5B - Microscope and angled cutter. |
1991 |
ISO 2808-6Aa |
Paints and varnishes - Determination of film thickness. |
Method 6Aa - Magnetic flux measurement |
1991 |
ISO 2808-6Ab |
Paints and varnishes - Determination of film thickness |
Method 6Ab - magnetic pull-off principle. |
1991 |
ISO 2808-6Ba |
Paints and varnishes - Determination of film thickness |
Method 6Ba Eddy current principle. |
1991 |
ISO 2808-7A |
Paints and varnishes - Determination of film thickness |
Method 7A - Wheel gauge. |
1991 |
ISO 2808-7B |
Paints and varnishes - Determination of film thickness. |
Method 7B - Comb gauge. |
1991 |
ISO 2813 |
Meas. of specular gloss of non-metallic paint films |
Glossmeter 20, 60 or 85 deg. Paint, varnish, etc. Use. |
1978 |
ISO 4624 |
Paints and varnishes - pull-off test |
Tensile tester, cylinders, cutter and adhesive. Use. |
1978 |
ISO 7668 |
Anodized aluminium and aluminium alloys - Measurement of specular reflectance and specular gloss at angles of 20, 45, 60 or 85 degrees. |
Method A; 20 deg. Method C; 60 deg. Method D; 85 deg. |
1986 |
ISO 8289 |
Vitreous and porcelain enamels - Low voltage test for detecting and locating defects |
Sponge moistened with salt and dishwashing solution, applied voltage is 0-9V dc or 0-5V ac at 600-900Hz. Phenolphthalein added to soltion will show red colour at pinhole. |
1986 |
ISO 8289 |
Vitreous and porcelain enamels- Low voltage test for detectying and locating defects |
Reagent: 3g sodium nitrite in 100ml tap water + 2 drops dishwashing agent; 4 drops of phenolpthalein as visual indicator. Method A: 9V+-1volts, alarms below 90kO+-9kOhms. Method B: 24V+-4volts and kitchen tissue for 2 mins. |
1999 |
ISO 8501-1 |
SS 05 59 00. Prep. of steel: visual assessment of surface cleanliness. |
Pictures and text describing cleanliness. |
1988 |
ISO 8501-2 |
Preparation of steel surfaces before application of paints and related products - Visual assessment of surface cleanliness - Part 2: Preparation grades of previously coated steel substrates after localised removal of previous coatings. |
- |
- |
ISO 8501-3 |
Preparation of steel substrates before application of paints and related products - Visual assessment of surface cleanliness - Part 3 Preparation grades of welds, cut edges and other areas with surface imperfections |
Pictures and text describing 3 grades of preparation for various imperfections. |
2001 |
ISO 8502-3 |
Preparation of steel surfaces before application of paints and related products - Tests for the assessment of surface cleanliness - Part 3: Assessment of dust on steel surfaces prepared for paintiong (pressure-sensitive tape method) |
Sticky tape and special tape applicator |
- |
ISO 8502-4 |
Preparation of steel substrates before application of paints and related products. Group B. Methods for the ssessment of surface cleanliness. Part B4. Guide to the estimation of the probability of condensation on a surface to be painted. |
For air and surface temp: mercury or electronic accurate to 0.5 C. For air humidity: Whirling hygro. and tables accurate to 3% RH; digital hygrometers with polymer sensors accurate to 3% in range 0 to 100% RH, temp -40 to 70 C; digital hygro. salt bridge. |
1993 |
ISO 8502-6 CD |
Preparation of steel surfaces before application of paints and related products - Tests for the assessment of surface cleanliness - Part 6: Sampling of soluble impurities on surfaces to be painted - Bresle method |
Draft. An adhesive patch providing a sampling compartment for the extraction liquid is attached to the surface. The washing liquid is injected by syringe and then retrieved for chemical analysis. |
1992 |
ISO 8502-9 FDIS |
- |
Conductivity measurement. Salt ug/cm2 = 4000 x change in conductivity of soln uS. Change = [(salt + water) - (water)] |
- |
ISO 8503-1 |
Preparation of steel substrates before application of paints and related products - Surface roughness characteristics of blast-cleaned steel substrates - Part 1: Specs and defs for ISO surface profile comparators for asses. of abras. blast-cleaned surfs. |
Describes the comparator. |
1988 |
ISO 8503-2 |
Preparation of steel substrates before application of paints and related products - Surface roughness characteristics of blast-cleaned steel substrates - Part 2: Method for the grading of surf. prof. of abras. blast-cleaned steel - Comparator procedure |
Use of comparator. Classification into Fine, Medium and Course. |
1988 |
ISO 8503-3 |
Preparation of steel substrates before application of paint and related products - Surface roughness characteristics of blast-cleaned steel substrates -Part 3: Method for the cal. of ISO surf. comp, and determ. surf. prof. - Focusing microscope procedure |
How to check the surfaces of the ISO comparator with a microscope. |
1988 |
ISO 8503-4 |
Preparation of steel substrates before application of paint and related products - Surface roughness characteristics of blast-cleaned steel substrates -Part 4: Method for the cal. of ISO surf. comp, and determ. surf. prof. - Stylus instrument procedure |
How to check the surfaces of the ISO comparator with a stylus instrument complying with ISO 3274. |
1988 |
ISO 8504-1 |
Preparation of steel substrates before application of paints and related products. Group D, Methods for surface preparation. Part D1, General principles. |
Assessment of surfaces and selection of preparation method. |
1992 |
ISO/DIS 8503-5 |
Preparation of steel substrates before application of paints and related products - Surface roughness characteristics of blast-cleaned steel substrates - Part 5: Replica tape method for the determination of the surface profile. |
(Discussion doc) Replica tape and micrometric gauge. [Testex] |
1999 |